Elsevier Ltd 15

701. Impact of fabrication method on the photocatalytic efficiency of PAN/SRTIO₃@AL composite nanofibers
702. Impact of gas composition and reservoir heterogeneity on miscible sour gas flooding — A simulation study
703. Impact of relative permeability hysteresis on pressure transient behavior and storage capacity in underground gas storage with well interference
704. Impact of Sc³⁺/In³⁺ ions co-substitution on structural, magnetic, and microwave features of SrFe₁₂O₁₉ hexaferrites
705. Impact of solid-to-liquid lipid ratio on the gelation and emulsion properties of lamb myofibrillar protein gels
706. Impact of swift heavy ion-induced point defects on nanoscale thermal transport in ZnO
707. Impact of the A-site rare-earth ions (Ln³⁺ – Sm³⁺, Eu³⁺, Gd³⁺) on structure and electrical properties of the high entropy LnCr_0.2Mn_0.2Fe_0.2Co_0.2Ni_0.2O₃ perovskites
708. Impact of the Mg/Zn ratio on features of structural and magnetic properties in A-site stoichiometric nanosized spinel ferrites
709. Impact of the Ni/Co ratio on structural and magnetic properties in A-site stoichiometric nanosized spinel ferrites
710. Impact of the Sc³⁺/In³⁺ co-substitution on the structural, magnetic, and microwave characteristics of Co_0.5Ni_0.5Fe₂O₄ nanospinel ferrites
711. Impact of thermobaric conditions on phase content, magnetic and electrical properties of the CoFe₂O₄ ceramics
712. Impact of time and spatial discretization on adjoint operators: Example of stationary and transient saturated flows
713. Impact of ultrafine particles and secondary inorganic ions on early onset and progression of amyloid aggregation: Insights from molecular simulations
714. Implementation of capillary penetration coefficient on water sorptivity for porous building materials: An experimental study
715. Implementation of the panel data regression analysis in PCM integrated buildings located in a humid subtropical climate
716. Implementing positive peace education in schools: A systematic literature review of global practices
717. Improved mechanical strength and thermal resistance of porous SiC ceramics with gradient pore sizes
718. Improved MPPT technology for PV systems using Social Spider optimization (SSO): Efficient handling of partial shading and load variations
719. Improved results on finite-time synchronization of shunting inhibitory cellular neural networks with time-varying delays via impulsive pinning hybrid control
720. Improvement of plasma discharge performance at KTM tokamak
721. Improvement of strength and performance properties of copper wire during severe plastic deformation and drawing process
722. Improvement of the design of the plow-subsoiler-fertilizer to increase soil fertility
723. Improving inter-plant integration of syngas production technologies by the recycling of CO₂ and by-product of the Fischer-Tropsch process
724. Improving multidisciplinary hospital care for acute cerebral circulation disorders in Kazakhstan
725. Improving the efficiency and stability of perovskite solar cells through optimization of the hole-transport layer
726. Impulsive pseudo-parabolic equation with nonlinear Robin boundary condition
727. In silico design of biomass-to-hydrogen Pathways: A review
728. In vitro evaluation of electrochemically bioactivated Ti6Al4V 3D porous scaffolds
729. Incorporating virtual reality innovation in higher education services: A possibility for technology adoption
730. Incorporation of Co ions on the physical properties of NiO nanoparticles and fabrication of superior photo-response p-Co-doped NiO/n-Si heterostructure-based diodes
731. Increasing energy efficiency of rule-based fuzzy clustering algorithms using CLONALG-M for wireless sensor networks
732. Increasing PEM fuel cell performance via fuzzy-logic controlled cascaded DC-DC boost converter
733. Increasing strength and performance properties of bimetallic rods during severe plastic deformation
734. Indication of the color change on the oxidation properties of fragrant rapeseed oil during shelf storage
735. Indirect estimation of resilient modulus (M_r) of subgrade soil: Gene expression programming vs multi expression programming
736. Individual versus collaborative note-taking: Results of a quasi-experimental study on student note completeness, test performance, and academic writing
737. Inducing swirl flow inside the pipes of flat-plate solar collector by using multiple nozzles for enhancing thermal performance
738. Infinite rotational motion generation and analysis of a spherical parallel manipulator with coaxial input axes
739. Influence of axial magnetic field on angular distribution of charge and energy of laser produced slow and fast tungsten ion groups
740. Influence of boron- and barium-containing modifiers on the structure of low-chromium cast iron
741. Influence of competitive adsorption, diffusion, and dispersion of CH₄ and CO₂ gases during the CO₂-ECBM process
742. Influence of constant and alternating electric fields on the deformation and destruction of a liquid droplet
743. Influence of different Si sources on plasma electrolytic oxidation coating formation, morphology and composition
744. Influence of emulsion microbubbles on the flotation recovery of fine-dispersed chalcopyrite
745. Influence of enhanced electrogenicity on anodic biofilm and bioelectricity production by a novel microbial consortium
746. Influence of fullerene content on the properties of polyurethane resins: A study of rheology and thermal characteristics
747. Influence of fused filament fabrication parameters on the flexural strength of nylon
748. Influence of initial defects on the degradation of steel reinforced mortar exposed to cyclic wetting and drying environment based on 3D scanning
749. Influence of initial state and heating rate on phase transformation in Fe₆₆Ga₃₄ alloy
750. Influence of subsurface temperature on cryogenic fracturing efficacy of granite rocks from Kazakhstan
1 13 14 15 16 17 30